能不能在程序中输出两次PDF报告，这两次报告是不同的测量点和不同的视图

能不能在程序中输出两次PDF报告，这两次报告是不同的测量点和不同的视图。例如:

DISPLY/OFF
DISPLY/TERM,V(TEXT)
DISPLY/STOR,V(GRAPHV)
T(PROFS_2)=TOL/PROFS,-0.1000,0.1000
OUTPUT/FA(GSU_1)
OUTPUT/FA(POI_1)
OUTPUT/FA(POI_2)
OUTPUT/FA(POI_3)
OUTPUT/FA(POI_4)
OUTPUT/FA(POI_5)
OUTPUT/FA(POI_6)
OUTPUT/FA(POI_7)
OUTPUT/FA(POI_8)
OUTPUT/FA(POI_10)
OUTPUT/FA(POI_9)
OUTPUT/FA(POI_11)
OUTPUT/FA(POI_12)

DISPLY/OFF
DISPLY/TERM,V(TEXT)
DISPLY/STOR,V(GRAPHV)
T(POS_2)=TOL/POS,2D,0.5000
OUTPUT/FA(CIR_3)
OUTPUT/FA(CIR_5)
OUTPUT/FA(CIR_6)
OUTPUT/FA(CPR_3)

ENDFIL

有什么办法啊?谢谢呀!

------------------------------------------------------------------------
爱问才明白

DISPLY/OFF
DISPLY/TERM,V(TEXT)
DISPLY/STOR,V(GRAPHV)
T(PROFS_2)=TOL/PROFS,-0.1000,0.1000

DID(Sample) = DEVICE/INCR,'D:\Output\090107-???.pdf'
OPEN/DID(Sample), FDATA, V(DEFAULTFORMAT), OUTPUT

OUTPUT/FA(GSU_1)
OUTPUT/FA(POI_1)
OUTPUT/FA(POI_2)
OUTPUT/FA(POI_3)
OUTPUT/FA(POI_4)
OUTPUT/FA(POI_5)
OUTPUT/FA(POI_6)
OUTPUT/FA(POI_7)
OUTPUT/FA(POI_8)
OUTPUT/FA(POI_10)
OUTPUT/FA(POI_9)
OUTPUT/FA(POI_11)
OUTPUT/FA(POI_12)

CLOSE/DID(Sample)

DISPLY/OFF
DISPLY/TERM,V(TEXT)
DISPLY/STOR,V(GRAPHV)
T(POS_2)=TOL/POS,2D,0.5000

DID(Sample) = DEVICE/INCR,'D:\Output\090107-???.pdf'
OPEN/DID(Sample), FDATA, V(DEFAULTFORMAT), OUTPUT

OUTPUT/FA(CIR_3)
OUTPUT/FA(CIR_5)
OUTPUT/FA(CIR_6)
OUTPUT/FA(CPR_3)

CLOSE/DID(Sample)

ENDFIL

把输出语句放在定义的步长设备的打开/关闭中间[蓝色语句]试试

------------------------------------------------------------------------
爱科腾瑞（北京）有限公司

谢谢斑竹，我试试

------------------------------------------------------------------------
爱问才明白

那些都是输出语句吗，要输出几次就加几句就可以了吗

呵呵，谢谢！！！！！！！！！！！！

------------------------------------------------------------------------
DMIS 空间--欢迎您！

我试了一下，还是不能使用不同的视图，比如第一次只输出点的视图报告，第二次再输出孔位的视图报告而不需要再回到D:\REPORT里抓取接受新视图一次了.

------------------------------------------------------------------------
爱问才明白